Search result(s): 511 - 525 of 619 » Department » Engineering

a cuckoo search based co-ordination of distributed generation units and shunt capacitor bank in radial distribution networks

This research work presents the Application of Cuckoo Search Algorithm for the simultaneous placement of distributed generation units and shunt capacitor banks in radial distribution networks. The approaches used in most literatures for determining the optimal allocation of DG units and Capacitor banks did not consider the simultaneous placement of... Continue Reading

Engineering

design, simulation, construction and performance evaluation of a solar box cooker

A solarbox cooker is a device that converts solar energy into useful heat in a confined space. The solar cooking system which captures and utilizes the abundant solar energy was designed, simulated, constructed and tested. Plane reflectors were used to concentrate solar radiations continuously on the collector which result to heat gain. It is usual... Continue Reading

Engineering

development of transitional probability matrix model for pavement design

A model of transitional probability matrix for Mechanistic-Empirical Pavement Design was developed with the aim of tarnishing the traditional method obtained from the judgment of an expert panel. The model was developed using fatigue and rutting as the critical factors in pavement failure. Model performance was assessed using first order reliabilit... Continue Reading

Engineering

development and optimization of the threshing performance of a multicrop thresher

The existing IAR multicrop thresher was evaluated and found to have low feed rate and output with millet and soybean crops. The machine was modified and reconstructed to increase its threshing performance. Its components were increased in size and a shredder was added below the feed hopper to cut stems of crops that entangle the threshing cylinder ... Continue Reading

Engineering

development of a modified token based congestion control scheme with adaptive forwarding for opportunistic network

This research presents the development of a modified token-based congestion control scheme with adaptive forwarding mechanism (mTBCC) algorithm for addressing congestion problems in opportunistic networks (OppNets). The algorithm addresses the limitations associated with the standard token �“based congestion control (TBCC) in terms of its ability ... Continue Reading

Engineering

development of an improved short-term peak load forecasting model based on seasonal autoregressive integrated moving average and nonlinear autoregressive neural network for nigeria power system grid

Electricity demand forecasting is a central and integral process for planning periodical operations and facility expansion in the electricity sector. Demand pattern is very complex due to the highly unpredictable behavior of consumers load consumption. Therefore, finding an appropriate forecasting model for a specific electricity network at peak de... Continue Reading

Engineering

development of conceptual models for plants and equipment procurement in tertiary institutions in kaduna state

This research sole aim is to improve on the development of conceptual procurement models that can create direct and indirect impacts of various forms of plant and equipment procurement in Kaduna state Tertiary Institutions in relation to, need assessment, delay in completion, costs and non-conformance with specification by suppliers and installatio... Continue Reading

Engineering

development of firefly algorithm based method for distributed generation planning in an unbalanced three-phase distribution network using voltage stability index

This research work presents development of Firefly algorithm (FA) and application of voltage stability index (VSI) for optimal planning of Distribution Generation (DG) in an unbalanced threephase distribution network. The VSI was used to find the DG location while the FA was used for the DG sizing. The developed method was implemented on standard I... Continue Reading

Engineering

development of pilot size process for zeolite y and zsm-5 production from kankara kaolin

The successes recorded at the laboratory for the synthesis of zeolite Y and ZSM-5 using Kankara kaolin sourced from Katsina state, Nigeria as starting material necessitated the need for upscale of the production process. This thesis focused on the development of three pilot size production units and characterizing the products obtained from those u... Continue Reading

Engineering

the effect of periwinkle shell ash and dust on the compressive strength of concrete

The study examined the partial replacement of Ordinary Portland Cement (OPC) with Periwinkle shell Ash (PSA) and Periwinkle Shell Dust which was obtained from burning 200kg of Periwinkle shell at 6000C and grinding 200kg with ball mill respectively. Concrete cubes were prepared from design mix with target strength of 20N/mm2, 25N/mm2, 30N/mm2 and 4... Continue Reading

Engineering

development of a dynamic output-feedback regulator for stabilization and tracking of non-square multi-input multi-output systems

This research work is aimed at the development of an observer-based dynamic output feedback controller for stabilization and tracking of nonlinear systems. The developed controller is designed after the immersion-invariance and internal model principle (IMP) frameworks and targets non-square systems such as rotational-translational actuator (RTAC),... Continue Reading

Engineering

failure evaluation of engineering projects in nigeria

(A CASE STUDY OF PIPELINE AND PRODUCT MARKETING COMPANY LIMITED, A SUBSIDIARY OF NIGERIAN NATIONAL PETROLEUM CORPORATION)

This study centres on Failure Evaluation of Engineering Projects in Nigeria, A case study of Pipeline and Product Marketing Company Limited (PPMC). The instrument used in this study is analysis of some randomly selected Projects and questionnaires administered to Professionals involved in the execution of projects in PPMC. The result of this study ... Continue Reading

Engineering

development of a modified east-west interface for distributed control plane in software defined network for wide area networks

This research is aimed at the development of a modified East-West Interface for distributed control plane in Software Defined Network (SDN) for Wide Area Network (WAN). The East-West Interface is important in achieving communication across a Software Defined WAN, to enable scalability and distribution of the control plane. The Communication Interfa... Continue Reading

Engineering

assessment of sawdust activated carbon (sac) in the treatment of aquaculture effluent

This study is aimed at the assessment of sawdust activated carbon in the treatment of aquaculture effluent with various objectives which includes the determination of the SAC properties, effluent parameters, effect of operating conditions and application of relevant adsorption isotherms. The sawdust was first precarbonized at 500?C, then impregnate... Continue Reading

Engineering

design of water supply (cold and hot) system of a three bedroom bungalow with adequate pressure

This research is focused on the design of water supply (cold and hot) system of a three bedroom bungalow with adequate pressure. Polypropylene (PP) pipes imported from Italy and polyvinyl chloride (PVC) pipes made in Nigeria, the two most common plastic materials used for potable water supply lines were selected for the analysis and compared to fin... Continue Reading

Engineering

About e-Project Material Centre


e-Project Material Centre is a web service aimed at successfully assisting final year students with quality, well-researched, reliable, and ready-made project work. Our materials are recent, complete (chapter 1 to Minimum of Chapter 5, with references), and well-written. INSTANT ACCESS! INSTANT DOWNLOAD. Simply select your department, choose from our list of topics available, and explore your data.

Why Students Love to Use e-Project Material?


Guaranteed Delivery: Getting your project delivered on time is essential. You cannot afford to turn in your project past the deadline. That is why you must get your project online from a company that guarantees to meet your deadline. e-Project Topics Material Centre is happy to offer instant delivery of projects listed on our website. We can handle just about any deadline you send our way. Satisfaction Guaranteed: We always do whatever is necessary to ensure every customer's satisfaction.

Disclaimer


e-Project Topics Material Centre will only provide projects as a reference for your research. The projects ordered and produced should be used as a guide or framework for your own project. The contents of the projects should help you generate new ideas and thoughts for your own project. It is the aim of e-Project Topics Centre to only provide guidance by which the projects should be pursued. We are neither encouraging any form of plagiarism nor are we advocating the use of the projects produced herein for cheating.

Terms and Conditions


Using our service is LEGAL and IS NOT prohibited by any university/college policies. You are allowed to use the original model papers you will receive in the following ways:
  • As a source for additional understanding of the subject
  • As a source for ideas for your own research (if properly referenced)
  • For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase) Direct citing (if referenced properly)
Thank you so much for your respect to the author's copyright.

Refund and Privacy Policy


  • Refunds: All sales are final. However, if you encounter any issues with accessing your purchased material, kindly contact our support team for immediate resolution.
  • Privacy Policy: Your personal information is protected and will not be shared with third parties. We ensure secure payment processing and data confidentiality.

Contact Information