modeling, analysis and simulation of a dc grid single ended primary inductance converter for dc load
This research studied a circuit topology of a solar based Single Ended Primary Inductance Converter (SEPIC) system and a battery furnishing a permanent magnet dc motor with current via a dc grid. The complete model equations of the entire system were derived. Harmonic balance technique was used to determine the converter steady state and ripple qua... Continue Reading
design and environmental - behaviour modelling of a bluetooth controlled planter robot
This research is aimed at the design and implementation of a Bluetooth controlled planter robot. It involved a mechanical design, a Bluetooth control design, an implementation of prototype and environmental behaviour modelling as well as validation of the robot’s model. The design was optimized for planting maize as a case study in Zaria. In the ... Continue Reading
carrier propagation on the shiroro complex 132kv transmission lines
This project aims at assessing the carrier propagation on a specified section of NEPA overhead powerlines, namely, the Shiroro Complex 132kV lines. Following an overview discussion of powerline carrier communication systems, consideration was given to the type of parameters required for assessing the communication system on the Shiroro Complex. Lin... Continue Reading
effect of some vegetable based oil as lubricants on the extrusion of aluminium
Four vegetable based oils were used as trial lubricants in the extrusion of aluminium billet through four different die geometries. These oils were extracted from Castor seeds, Neem seeds, Jatropha seeds and Cotton seeds respectively. Results obtained from this work as compared with other works done in the area shows that these oils were found to b... Continue Reading
application of fibre reinforced concrete in the design and construction of tension controlled structures
Linear-elastic theory of fracture mechanics was reviewed and a proposed method for designing structural elements subjected principally to tension presented, based on the strain-energy-release-rate for the fibrous concrete mixes. Eighteen experimental models were provided and of which seventeen were tested and reported including the load ranges and ... Continue Reading
gasification of liquid fuels
Analysis of the results of the simulation for the production of gaseous fuel by gasification of kerosene was made. Also treated, were the possible methods of actualizing this principle. Simulation results showed that at ambient conditions, kerosene (DPK) can not support a flammable vapor and a liquid booster in form of petrol (PMS) was employed to ... Continue Reading
modeling and stabilization analyses of a microunmanned aerial vehicle system using a modified radio controlled-based helicopter
This work is aimed at modeling and carrying out state space analysis of a micro-UAV (unmanned aerial vehicle) which is based on a modified radio controlled (RC) coaxial helicopter. The modification involved incorporating payload such as: GPS (global positioning system) module, Arduino microcontroller board and the Arduino Wi-Fi shield. The modeling... Continue Reading
the functional form and energy stability of travel expenditures in nigeria
The characteristics of (ravel money expenditure in a Nigerian setting are examined, with special emphasis on the its functional form and energy stability, using the before and after the October 1994 fuel price increase situations. Preliminary analysis of travel charatcristics show general reduction in trip rates, with the least average reduction of... Continue Reading
the structure, petrology and geochemistry of the tibchi younger granite ring-complex, nigeria
The 1 :50,000 geological map of the Tibchi Complex presented is characterised by a closed elliptical ring-dyke framework hitherto unpredicted by pioneer workers. Major rock units comprise a basalt - potassic granite suite. The structural history of the Complex involved a central shield volcano, succeeded by a caldera and fluidised intra-caldera vol... Continue Reading
production of bioethanol from elephant grass (pennisetum purpureum) stem
The production of bio-ethanol from Elephant grass (Pennisetun purpureum) stem was carried out using elephant grass stem as a feedstock and a combination of Aspergillus niger at 0.2%(w/v) 0.4%(w/v), 0.6%(w/v), 0.8%(w/v) and 1%(w/v) concentrations and Saccharomyces cerevisiae (brewer’s yeast) at 0.5% (w/v), 1%(w/v), 1.5%(w/v), 2%(w/v) and 2.5%(w/v)... Continue Reading
synthesis of biolubricant from vegetable oils
This thesis aimed at the production of biolubricant from vegetable oils. The first stage produced methyl ester of the oil and in the second stage; the methyl ester was transesterified with Trimethylolpropane (TMP) in a ratio of 3.5:1 at 1500C to produce the biolubricant. The pour points biolubricant and its blend were significantly improved when co... Continue Reading
building response to dynamic loads due to quarry blasting
The Existence of quarries near residential areas is now becoming inevitable. In order to protect building Structures against quarry operations hazards, there is need to quantify response of these structures to hazards. One of such hazards is the dynonic loads emitted and transmitted through the soil and air media due to blasting of the rock for its... Continue Reading
experimental performance evaluation of laboratory and field solar and hybrids crop dryers
Five small scale and two medium scale crop dryers with and without rockbed heat store well as a hybrid crop dryer, suitable for crop drying in different locations in savanna of Norther Nigeria were designed, constructed and lab-tested in IAR/ABU, Zaria The full capacity of the small scale dryers are 50kg of maize grain, 20kg of fresh tomatoes and 1... Continue Reading
suitability of local vegetable oils for cold extrusion of aladja st60-2 structural stbel
The performance of some vegetable oils (palm oil groundnut oil, soya bean oil, and shea butter oil) as lubricants in the cold extrusion of Aladja ST60-2 structural steel has been investigated in the direct extrusion of 13mm diameter slugs with different initial billet lengths at various extrusion ratios and speeds. The performance criteria employed... Continue Reading
a study of the influence of stopped delay on driver gap acceptance behaviour
The influence of stopped delay on driver gap acceptance behaviour is investigated. Gap rejection/acceptance data collected for minor road drivers executing left-turning manoeuvres at two separate priority intersections are analysed. The mean critical gapfit (C) and its variance (O2) are separately estimated from the aggregated data and from abstrac... Continue Reading
About e-Project Material Centre
e-Project Material Centre is a web service aimed at successfully assisting final year students with quality, well-researched, reliable, and ready-made project work. Our materials are recent, complete (chapter 1 to Minimum of Chapter 5, with references), and well-written. INSTANT ACCESS! INSTANT DOWNLOAD. Simply select your department, choose from our list of topics available, and explore your data.
Why Students Love to Use e-Project Material?
Guaranteed Delivery: Getting your project delivered on time is essential. You cannot afford to turn in your project past the deadline. That is why you must get your project online from a company that guarantees to meet your deadline. e-Project Topics Material Centre is happy to offer instant delivery of projects listed on our website. We can handle just about any deadline you send our way. Satisfaction Guaranteed: We always do whatever is necessary to ensure every customer's satisfaction.
Disclaimer
e-Project Topics Material Centre will only provide projects as a reference for your research. The projects ordered and produced should be used as a guide or framework for your own project. The contents of the projects should help you generate new ideas and thoughts for your own project. It is the aim of e-Project Topics Centre to only provide guidance by which the projects should be pursued. We are neither encouraging any form of plagiarism nor are we advocating the use of the projects produced herein for cheating.
Terms and Conditions
Using our service is LEGAL and IS NOT prohibited by any university/college policies. You are allowed to use the original model papers you will receive in the following ways:
- As a source for additional understanding of the subject
- As a source for ideas for your own research (if properly referenced)
- For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase) Direct citing (if referenced properly)
Refund and Privacy Policy
- Refunds: All sales are final. However, if you encounter any issues with accessing your purchased material, kindly contact our support team for immediate resolution.
- Privacy Policy: Your personal information is protected and will not be shared with third parties. We ensure secure payment processing and data confidentiality.
