application of fuzzy c-means clustering and particle swarm optimizationto improve voice traffic forecastingin fuzzy time series
Forecasting of voice traffic using an accurate model is important to the telecommunication service provider in planning a sustainable Quality of Service (QoS) for their mobile networks. This work is aimed at forecasting Erlang C �“ based voice traffic using a hybrid forecasting model that integrates fuzzy C-means clustering (FCM) and particle swar... Continue Reading
characterisation of some nigerian coals for power generation
Five coal samples from Odagbo (Kogi State), Owukpa (Benue State), Ezimo (Enugu State), Amansiodo (Enugu State) and Inyi (Enugu State) weresubjected to proximate analysis, ultimate analysis, calorific value determination, petrographic and thermogravimetric analysis to determine their suitability for power generation. Tests were carried out at the la... Continue Reading
techno-economic evaluation of selexol-based co2 capture process for ashaka cement plant
This research work assessed the technology used for cement plant by employing an old cement plant with post-combustion CO2 capture using a novel physical solvent (Selexol) commonly known as dimethyl ether polyethylene glycol. The CO2 capture plant was simulated using Aspen Hysys software after the flue gas analysis of the cement plant was carried o... Continue Reading
synchronous machine parameter extraction from real time operating data
A method is proposed for extracting the parameters of a round rotor synchronous machine using real time operating data. The machine is modelled mathematically as a set of differential equations. These equations are linearized into algebraic equations from where the unknown parameters �“ stator resistance s r , stator leakage inductance ls L , dire... Continue Reading
suitability of some common nigerian timber species for use as simply supported bridge beams using eurocodessuitability of some common nigerian timber species for use as simply supported bridge beams using eurocodes
The work presented EN338 (2009) strength classification for some common Nigerian timber species namely: Antiaris africana, Guarea cedrata, Piptadeniastrum africanum, and Isoberlinia tomentosa. The work also assessed the suitability of the Nigerian timber species for use as simply supported bridge beams according to EN1995-1-1(2004), EN1995-2(2004),... Continue Reading
suitability of orange peels, banana peels and recycled low density polyethylene (rldpe) composites for particleboard manufacturing
The aim of this study was to investigate the suitability of using orange and banana peels as alternatives to wood-based particleboard composites. The orange and banana peels composite boards were produced by compressive molding using recycled low density polyethylene (RLDPE) as binder. The RLDPE was varied from 30 to 70wt% with interval of 10wt%. F... Continue Reading
stochastic evaluation of offshore carbon fibre reinforced concrete platforms on aluminum girders
A stochastic evaluation of the performance of Carbon Fibre Offshore Plastics (CFRP) offshore platform consideringsubmerged and partially submerged environmental conditions wasanalyzed usingSwedish code,Boverket (2004). A Probability-based analysis using First Order Reliability Method (FORM) was used to determine the safety index of the deck conside... Continue Reading
production of biogas from the anaerobic co-digestion of tannery fleshing and cow-dung enhanced by sodium and calcium alginates
The subjects of interest in this work were the production of biogas via anaerobic co-digestion of tannery fleshing and cow-dung; and the reduction of sulphide concentration by direct inclusion of sodium and calcium alginate. Comparison of the efficacy of various tannery beam house effluents as substrate diluents indicated that the soaking liquor wa... Continue Reading
development of environmentally friendly biodegradable cutting fluid from soya beans (glycine max)
In this work, cutting fluid emulsion was developed from soya beans and the performance of the developed cutting fluid was evaluated by comparison with the conventional cutting fluid (control sample), using its ability to effectively perform as coolant during machining operation. The machining operation employed was the turning operation in which ch... Continue Reading
stochastic section modulus requirement for carbon fibre reinforced plastic pultruded beams
Six Carbon Fibre Reinforced Plastic (CFRP) pultruded beam section from The Pultex� Pultrusion Design Manual Volume 4 - Revision 8 Copyright � 2004 by Creative Pultrusions Inc., were assumed to be simply supported doubly symmetric I-section, with uniformly distributed load of 3.5kN/m2 applied over the length of 3.050m each. A comparative analysis ... Continue Reading
stabilization of black cotton soil with lime- iron ore tailing blend
A black cotton soil collected from Deba Local Government Area of Gombe state classified as A-7-6 (25) or CH in AASHTO and Unified Soil Classification System (USCS), respectively. It was treated with lime �“ iron ore tailing (IOT) blend in stepped concentration of 0, 2, 4, 6 and 8 % lime as well as 0, 2, 4, 6, 8, and 10 % IOT by dry weight of soil.... Continue Reading
stabilization of black cotton soil with iron ore tailing
Results of preliminary investigation of the natural black cotton soil used in the study shows that it belongs to A �“ 7 �“ 6 (13) or CH in the AASHTO and Unified Soil Classification System (USCS), respectively. Soils under these groups are highly plastic and of poor engineering benefit. The soil was treated with up to 16% iron ore tailing, IOT (a... Continue Reading
radial distribution network modeling and analysis considering power flow and reconfiguration
(A CASE STUDY OF AZARE DISTRIBUTION NETWORK)
The complexity and large number of computations involved in power flow and reconfiguration analysis of large distribution networks necessitates the need for the improvement of power flow and reconfiguration techniques. In this research work, a GPS based method is used in modeling Azare distribution network and in selecting the most appropriate posi... Continue Reading
process intensification on biodieselproduction from jatrophacurcas seed oil
The challenges of continual depletion, economic crisis and environmental issues of the petroleum fuels have attracted the scientists’ interest to seek for alternatives to fossil fuels. Biodiesel is the alternative to petrol diesel because; it has similar physicochemical properties to petrol diesel. However, biodiesel has not been competing favour... Continue Reading
estimation of detection threshold for spectrum sensing in cognitive radio using adaptive neurofuzzy inference system and monte carlo techniques
An important component of cognitive radio is spectrum sensing to detect the presence or absence of primary (licensed) user in the spectrum band of interest. However, the traditional static spectrum allocation strategies cause temporal and geographical holes of spectrum usage in licensed bands. Spectrum occupancy was categorized into completely free... Continue Reading
About e-Project Material Centre
e-Project Material Centre is a web service aimed at successfully assisting final year students with quality, well-researched, reliable, and ready-made project work. Our materials are recent, complete (chapter 1 to Minimum of Chapter 5, with references), and well-written. INSTANT ACCESS! INSTANT DOWNLOAD. Simply select your department, choose from our list of topics available, and explore your data.
Why Students Love to Use e-Project Material?
Guaranteed Delivery: Getting your project delivered on time is essential. You cannot afford to turn in your project past the deadline. That is why you must get your project online from a company that guarantees to meet your deadline. e-Project Topics Material Centre is happy to offer instant delivery of projects listed on our website. We can handle just about any deadline you send our way. Satisfaction Guaranteed: We always do whatever is necessary to ensure every customer's satisfaction.
Disclaimer
e-Project Topics Material Centre will only provide projects as a reference for your research. The projects ordered and produced should be used as a guide or framework for your own project. The contents of the projects should help you generate new ideas and thoughts for your own project. It is the aim of e-Project Topics Centre to only provide guidance by which the projects should be pursued. We are neither encouraging any form of plagiarism nor are we advocating the use of the projects produced herein for cheating.
Terms and Conditions
Using our service is LEGAL and IS NOT prohibited by any university/college policies. You are allowed to use the original model papers you will receive in the following ways:
- As a source for additional understanding of the subject
- As a source for ideas for your own research (if properly referenced)
- For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase) Direct citing (if referenced properly)
Refund and Privacy Policy
- Refunds: All sales are final. However, if you encounter any issues with accessing your purchased material, kindly contact our support team for immediate resolution.
- Privacy Policy: Your personal information is protected and will not be shared with third parties. We ensure secure payment processing and data confidentiality.
