Search result(s): 121 - 135 of 620 » Department » Engineering

optimum performance of a battery of wells using a ccmputer simulation model

This study investigates the optimum use to which a number of wells, sunk for water supply to the Ipaja Housing Estate in Lagos State could be put. The study is in two parts. The first part involves graphical analysis of the available pumping test data from sixteen wells located within the estate to determine the hydraulic characteristics of the und... Continue Reading

Engineering

structural synthesis using stochastic programming

This paper reports the investigation on the reliability levels implicit in the BS8110 requirements, probability-based optimum design and sensitivity tests for singly reinforced continuous beams. These are accomplished with the aid of the modern reliability analysis (First-Order Reliability Integration Scheme- F0RM5, Gollwitzer, et al,1988) and a No... Continue Reading

Engineering

settling characteristics of kubanni dam water

This study investigates the settling characteristics of the raw water of Kubanni Dam at the main campus of Ahmadu Bello University, Zaria. The investigation included plain sedimentation and sedimentation of coagulated water samples using aluminium sulphate (alum) as coagulant. Coagulation and flocculation tests were performed by the batch method in... Continue Reading

Engineering

strain-rate influence on shear strength characteristics of compacted fadama clay

This study is concerned with the investigation of strain-rate effects on shear strength characteristics of saturated compacted Fadama Clay. The experimental program consisted of consolidated undrained triaxial test with controlled strain-rate. The rates of strain adopted are 0.0024, 0.006, 0.012 and 0.03 in/min. (0.08, 0.2, 0.4 and 1.0 %/min., resp... Continue Reading

Engineering

the comparison of speed, cost and accuracy of traversing using edm, odm and steel tape

The Comparisonof Speed, cost and^accuracv of traversing usinq EDM, ODM and Steel tape A built-up area (Faculty of Enqineerinq) within the Ahmadi Bello University. Samaru Campus was traversed emplovinq theodolite with three methods of linear measurements. The obiective was to comparatively and statistically analyse the computed results of each of th... Continue Reading

Engineering

quality of sandcrete hollow blocks produced in benue state

The project is a study of the physical properties of sandcrete hollow blocks produced in Benue State for the purpose of ascertaining their quality. Following a careful site survey of thirty block industries across the state, five block industries were chosen for assessement and about fifty blocks were randomly selected from each of them. Majority o... Continue Reading

Engineering

diurnal, seasonal and topographical effects on vertical refraction

In this investigation, the effect of season, time of the day and topography has been examined. Two lines, one on water of length 1098.650 meters and the other 1287.05 meters on land were selected for the study. Coefficient of refractions on these two lines for different time of the day - 0800 hours to 1600 hours and for different seasons - dry and ... Continue Reading

Engineering

toll booth congestion studies at the lagos - ibadan expressway

The problems of organization to meet the rising tide of traffic congestion, patron complaint and increased costs appear, for some time now, to characterize the operation of vehicular toll collection at the Lagos - Ibadan expressway toll booth. It is the principal purpose of this research to study the weekend peak traffic delays at this facility by ... Continue Reading

Engineering

a review of areas and volumes in earthworks

Various approaches for computing cross sectional areas in earthworks are treated. Proofs of different formulae in the calculations are given, including some examples on the applications. Each method is analysed with sufficient depth in order to easily infer its merit and limitations. The methods, considered comparatively, are synthesized and their ... Continue Reading

Engineering

development of sheet steel groundcoat enamel from local raw materials

An investigation into the development of sheet steel groundcoat enamel from local raw materials was carried out. These local raw materials included: feldspar, quartz, magnesite, whiting, baryte and manganese dioxide. Several formulations were made. Of the five formulations that yielded best performance properties, enamel B had the highest local inp... Continue Reading

Engineering

a statistical model of flow levels in river lokko - adamawa state

Monthly water levels for four years in Lokko river were studied statistically using the time series theory, and an ARMA (1.1) model was identified as suitable to describe the data. An estimation model was developed, the results obtained were found to be satisfactory, except in the rainy season when the error could be as high as 37 percent on the av... Continue Reading

Engineering

reliability analysis of prestressed electric transmission concrete poles

Reliability and economy are inherently competing demands; the study of which is becoming an increasing concern for the designers of electric transmission line structures and more generally to the profession of Structural Engineering. The work covered in this study deals with the assessment of the reliability (safety) levels of the prestressed elect... Continue Reading

Engineering

estimation of streamflow in the upper benue river basin using climatic water budget method

Water is a fundamental element in the economic and social development of any country. A survey of surface water development in the Upper Benue Basin is made here in and availability of necessary data for water resources development discussed. A set of average monthly Temperature and Rainfall data have been used to estimate monthly streamflow values... Continue Reading

Engineering

sampling of land use from large scale aerial photographs

A land use classification has been developed for the inventory of land use in a Nigerian forest area, Sabon Gida Ora, using large scale aerial photography. The dot grid method of sampling covering 14% of the area is used in estimating the various land use categories. Bonnor (1975) and Kolbl and Trachsler (1980) formula are used in estimating the er... Continue Reading

Engineering

developing statistical programs on a micro computer for surveying data analysis

The project produces a statistical computer package for analysis of survey data. The computer programes are sequentially developed to cover statistical concepts such as, measure of central tendency, measures of dispersion, graphical presentation of data (Histogram, Stemplot, Boxplot, Frequency Table, Scatter Diagram etc.); probability functions and... Continue Reading

Engineering

About e-Project Material Centre


e-Project Material Centre is a web service aimed at successfully assisting final year students with quality, well-researched, reliable, and ready-made project work. Our materials are recent, complete (chapter 1 to Minimum of Chapter 5, with references), and well-written. INSTANT ACCESS! INSTANT DOWNLOAD. Simply select your department, choose from our list of topics available, and explore your data.

Why Students Love to Use e-Project Material?


Guaranteed Delivery: Getting your project delivered on time is essential. You cannot afford to turn in your project past the deadline. That is why you must get your project online from a company that guarantees to meet your deadline. e-Project Topics Material Centre is happy to offer instant delivery of projects listed on our website. We can handle just about any deadline you send our way. Satisfaction Guaranteed: We always do whatever is necessary to ensure every customer's satisfaction.

Disclaimer


e-Project Topics Material Centre will only provide projects as a reference for your research. The projects ordered and produced should be used as a guide or framework for your own project. The contents of the projects should help you generate new ideas and thoughts for your own project. It is the aim of e-Project Topics Centre to only provide guidance by which the projects should be pursued. We are neither encouraging any form of plagiarism nor are we advocating the use of the projects produced herein for cheating.

Terms and Conditions


Using our service is LEGAL and IS NOT prohibited by any university/college policies. You are allowed to use the original model papers you will receive in the following ways:
  • As a source for additional understanding of the subject
  • As a source for ideas for your own research (if properly referenced)
  • For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase) Direct citing (if referenced properly)
Thank you so much for your respect to the author's copyright.

Refund and Privacy Policy


  • Refunds: All sales are final. However, if you encounter any issues with accessing your purchased material, kindly contact our support team for immediate resolution.
  • Privacy Policy: Your personal information is protected and will not be shared with third parties. We ensure secure payment processing and data confidentiality.

Contact Information