optimising patients flow and resources utilisation in the out-patient department of a public hospital a case study of yusuf dantsoho memorial hopital kaduna
Queuing theory as a tool for optimising patients flow and resources utilisation in the female section of the OPD at Yusuf Dantsoho memorial hospital Kaduna, the study was conducted for a period of 5 days. Simple queuing theory calculations were done using the data collected in the evaluation of the performance characteristics of the system, i.e. th... Continue Reading
development of a deep learning based vehicle license plate detection scheme
This research developed a license plate and classification scheme using deep learning architecture which utilized transfer learning using pre-trained Convolutional Neural Network (CNN). The developed scheme used images obtained from Caltech dataset, Peking University VehicleID (PKU VehicleID) dataset and a developed dataset of vehicle licence plate... Continue Reading
development of a fuzzy time series model using cat swarm optimization clustering and optimized weights of fuzzy relations
This research developed a hybrid forecasting technique that integrates Cat Swarm Optimization Clustering (CSO-C) and Particle Swarm Optimization (PSO) algorithms with Fuzzy Time Series (FTS) forecasting model. Cat Swarm Optimization Clustering (CSO-C) which is an algorithm for data classification is adopted at the fuzzification stage to objectively... Continue Reading
development of a shunt active power filter for harmonic reduction using synchronous reference frame with space vector pulse width modulation
This work aimed at designing and implementation of Shunt Active Power Filter (SAPF) for power quality improvement through harmonic reduction. The current harmonics are being caused by nonlinear characteristic of power electronics based equipments which increase power losses and in turn reduce power quality. This work employed a three phase three wi... Continue Reading
assessment of municipal solid waste impact on groundwater quality of some selected areas
(A CASE STUDY OF MAIDUGURI, NIGERIA)
This study assessed the impact of open dumpsites on the quality of groundwater within the vicinity of solid waste dumpsites in Maiduguri. The problem of rapid urbanization and poor waste management has resulted in an increased of hand dug wells with some located within the premises of an open dumpsites. The mean percentage composition of solid wast... Continue Reading
development of a state estimation based improved detection and localization of non-technical losses using smart meter measurements
This research work presents the development of branch current based state estimation for Non-Technical Losses (NTLs) Detection and Localization. The use of weighted least square (WLS) state estimation for the evaluation of branch current of a network during theft is considered. In order to confirm the presence of theft in a network, current measure... Continue Reading
development of a distributed big data fusion architecture for machine-to-machine communication using ensemble learning
This research developed a distributed big data fusion architecture for machine to machine communication using ensemble learning. This is implemented to mitigate the challenges that characterize centralized big data fusion architecture commonly adopted through the use of Hadoop MapReduce platform. These challenges include bandwidth consumption, late... Continue Reading
effective training as a tool for improving building services in engineering practice
It has being observed over time that there are problems associated with the quality of designs and execution of jobs within the Building Services Sector of the Engineering Industry. The sector is an important aspect of Engineering Practice in Nigeria and its performance can only be measured by the quality of its output which include good engineerin... Continue Reading
performance evaluation of different materials as chills in sand casting of aluminium alloy
This study has evaluated the effectiveness of metallic materials as chill in sand casting of aluminium alloy. Four plates of dimension 165mm x 80mm x10mm were cast using sand mould. Steel, copper and brass chills in form of cylindrical bar of geometry 7mm in diameter and 50mm long were inserted, side by side at regular intervals of 30mm in each san... Continue Reading
development of a privacy aided trust routing algorithm based on social similarity in opportunistic network
This research work presents the development of a privacy aided trust routing model using social similarity in an Opportunistic Network (OppNet). OppNet is a delay tolerant network where link is highly unpredictable. It is an ideal solution in situations where the deployment of wired and conventional wireless networks is difficult or practically imp... Continue Reading
modal analysis of vertically curved concrete fly-over bridges
The effectiveness and sensitivity of vertically curved concrete flyover bridge (VCCFB) profile is presented. Modal analysis was conducted on three VCCFB models; one for a profile achieved using horizontal beams, profile achieved using slightly curved beams and a profile achieved using combination of straight and curved beams. Twelve vibration mode ... Continue Reading
reliability-based analysis of composite solid slender timber columns with aluminium laminates using selected nigerian timber species
Four timber species (Strombosia pustulata, Macrocarpa biquertii, Entandrophragma cylindricum and Nauclea diderichii) were laminated with aluminium sheets of varying thicknesses.Axial and flexural loads were applied to the composite columns to determine their behaviour under such loadings. Finite element analysis was carried out in Abaqus/CAE 6.10 (... Continue Reading
synthesis, formulation and characterization of phenol formaldehyde/chitosan composites
The methodology of the experiment involves three main stages. The first part describes the synthesis of the PF (novolac) resins. Novolac (resins) were prepared with an excess of phenol over formaldehyde under acidic conditions. PF molar ratio were varied from 1P:2F to 1P:8F. The structure of the PF was determined using FT-IR techniques. The prepara... Continue Reading
development of an improved application specific tunelling protocol selection scheme for site to site virtual private networks
This dissertation presents the development of an improved application specific tunnelling protocol selection scheme (iASTPSS) for site-to-site virtual private network (VPN). The aim is to develop an improved tunnelling protocol selection scheme for site to site VPN that is application specific, requiring security, bandwidth, and time sensitivity as... Continue Reading
development of an internet protocol traceback scheme for denial of service attack source detection
This dissertation presents the development of an Internet Protocol (IP) traceback scheme for the detection of a denial of service (DoS) attack source base on shark smell optimization algorithm (SSOA). Detection of the source of DoS attack is very important due to the serious damages the attack do cause and the need to bring the perpetrators to just... Continue Reading
About e-Project Material Centre
e-Project Material Centre is a web service aimed at successfully assisting final year students with quality, well-researched, reliable, and ready-made project work. Our materials are recent, complete (chapter 1 to Minimum of Chapter 5, with references), and well-written. INSTANT ACCESS! INSTANT DOWNLOAD. Simply select your department, choose from our list of topics available, and explore your data.
Why Students Love to Use e-Project Material?
Guaranteed Delivery: Getting your project delivered on time is essential. You cannot afford to turn in your project past the deadline. That is why you must get your project online from a company that guarantees to meet your deadline. e-Project Topics Material Centre is happy to offer instant delivery of projects listed on our website. We can handle just about any deadline you send our way. Satisfaction Guaranteed: We always do whatever is necessary to ensure every customer's satisfaction.
Disclaimer
e-Project Topics Material Centre will only provide projects as a reference for your research. The projects ordered and produced should be used as a guide or framework for your own project. The contents of the projects should help you generate new ideas and thoughts for your own project. It is the aim of e-Project Topics Centre to only provide guidance by which the projects should be pursued. We are neither encouraging any form of plagiarism nor are we advocating the use of the projects produced herein for cheating.
Terms and Conditions
Using our service is LEGAL and IS NOT prohibited by any university/college policies. You are allowed to use the original model papers you will receive in the following ways:
- As a source for additional understanding of the subject
- As a source for ideas for your own research (if properly referenced)
- For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase) Direct citing (if referenced properly)
Refund and Privacy Policy
- Refunds: All sales are final. However, if you encounter any issues with accessing your purchased material, kindly contact our support team for immediate resolution.
- Privacy Policy: Your personal information is protected and will not be shared with third parties. We ensure secure payment processing and data confidentiality.
