Site Logo E-PROJECTTOPICS

DEVELOPMENT OF BAOBAB/SISAL REINFORCED LOW DENSITY POLYETHYLENE HYBRID COMPOSITE


📝


Presented To


Engineering Department

📄 Pages: 99       🧠 Words: 12801       📚 Chapters: 5 🗂️️ For: PROJECT

👁️‍🗨️️️ Views: 206      

⬇️ Download (Complete Report) Now!

ABSTRACT
In this work, the properties of baobab/sisal fibre reinforced low density polyethylene hybrid composites were studied. The effect of fibre loading and fibre treatment with varying sodium hydroxide (NaOH)concentration on the composite properties was investigated. The developed composites were characterized for tensile strength, modulus of elasticity (MOE), elongation at break, hardness and impact strength.Analysis of the results showed that, for the monolithic composite,10 wt% baobab fibre loading had the bestmechanical property compared to other baobab fibre loadings, with tensile strength and MOEof 8.28 MPa and 127 MParespectively.The result ofNaOH treatment showed that 8 wt% treated fibre composite exhibited the best tensile strength, MOE, impact strength and the least percentage water absorption of 14.54 MPa, 245 MPa, 4.4 J/mm2 and 1.8% respectively.On hybridization with sisal, it was observed that the100% sisal fibre composite exhibited higher tensile strength and MOEof 12.47 MPa, 262.85 MPa, and the least percentage water absorption capacity of 0.37% but for both the hybrid were higher than the monolithic composite. The result of the NaOH treated hybrid composite showed that 6 wt% NaOH treated sisal/baobab fibre exhibited the best tensile strength, MOE and percentage water absorption of 17.08 MPa, 279.40 MPa, and 0.18% respectively which were higher than that of the monolithic sisal fibre reinforced composites. The fourier transforms infrared spectroscopy (FT-IR) analysis of untreated and treated baobab fibre showed that there was reduction in the hemicelluloses in the NaOH treated baobab fibres as indicated by the band at2277-2274 cm-1representing C=O stretching of hemicelluloses. The scanning electron microscope (SEM) analysis showed that composite produced from untreated fibre had more cracks and voids, possibly due topoor interaction between the fibre and low density polyethylene matrix, resulting in lower mechanical properties.The composite have properties whichsuggest their suitability for application in deck boards, dash board, rear seat barriers and guardrails systemsto replace the hardwood and metals currently used hence, preserving the environment.

PLEASE NOTE

This material is a comprehensive and well-written project, structured into Chapter (1 to 5) for clarity and depth.


To access the full material click the download button below


OR


Contact our support team via Call/WhatsApp: 09019904113 for further inquiries.

Thank you for choosing us!

📄 Pages: 99       🧠 Words: 12801       📚 Chapters: 5 🗂️️ For: PROJECT

👁️‍🗨️️️ Views: 206      

⬇️ Download (Complete Report) Now!

🔗 Related Topics

Development of EN 338(2003) Strength Classes of Doka (Isoberlinia doka), Madaci (Khaya senegalensis) Gawo (Acacia albida) and Rimi (Ceiba pentandra) Timber Species of Nigerian Origin DEVELOPMENT OF MEASUREMENT-BASED ADMISSION CONTROL ALGORITHM FOR EDGE CARRIER ETHERNET NETWORK TO REDUCE PACKET LOSS AND IMPROVE BANDWIDTH UTILIZATION OPTIMUM DESIGN OF THE THICKNESS OF CARBON FIBRE REINFORCED POLYMER MATERIAL (CFRP) REQUIRED FOR STRENGTHENING OF DEFICIENT REINFORCED CONCRETE BEAM PREPARATION AND APPLICATION OF ZnFe2O3/α- Al2O3 COMPOSITE PHOTOCATALYSTS FOR TEXTILE EFFLUENT TREATMENT DEVELOPMENT OF THREE DEGREE OF FREEDOM CONTROLLER FOR SHELL AND TUBE HEAT EXCHANGER USING NON-DOMINATED SORTING GENETIC ALGORITHM II STRESS DISTRIBUTION OF SHORT REINFORCED CONCRETE COLUMNS LOADED UNDER SMALL ECCENTRICITIES DEVELOPMENT OF A PRIVACY AIDED TRUST ROUTING ALGORITHM BASED ON SOCIAL SIMILARITY IN OPPORTUNISTIC NETWORK DEVELOPMENT OF A MODIFIED TOKEN BASED CONGESTION CONTROL SCHEME WITH ADAPTIVE FORWARDING FOR OPPORTUNISTIC NETWORK DEVELOPMENT AND CHARACTERIZATION OF Al-3.7%Cu-1.4%Mg ALLOY/PERIWINKLE ASH (Turritella communis) PARTICULATE COMPOSITES DEVELOPMENT AND CHARACTERIZATION OF RECYCLED HIGH DENSITY POLYETHYLENE (RHDPE)/NATURAL FIBRE COMPOSITES DEVELOPMENT OF CANNY OPERATOR BASED GUI FOR THE MEASUREMENT OF OPTICAL RETURN LOSS OPTIMUM DESIGN OF REINFORCED CONCRETE RAFT FOUNDATIONS USING FINITE ELEMENT ANALYSIS DEVELOPMENT AND OPTIMIZATION OF THE THRESHING PERFORMANCE OF A MULTICROP THRESHER DEVELOPMENT AND SIMULATION OF A SINUSOIDAL PULSE WIDTH MODULATION-BASED CONTROL SCHEME FOR IMPROVED EFFICIENCY AND TORQUE PRODUCTION IN SINGLE PHASE INDUCTION MACHINES DEVELOPMENT OF AN ACCEPTABLE USE POLICY FRAMEWORK FOR IBBUL COMMUNICATION NETWORK DEVELOPMENT OF A PROCESS ROUTE FOR THE BENEFICIATION OF MALLAM AYUBA MANGANESE DEPOSIT TO FERROMANGANESE FEED GRADE PREDICTION OF MOMENT CAPACITY OF CONCRETE SLABS SINGLY REINFORCED WITH CARBON FIBER REINFORCED PLASTICS (CFRP) USING SIMULATED ANNEALING APPLICATION OF FIBRE REINFORCED CONCRETE IN THE DESIGN AND CONSTRUCTION OF TENSION CONTROLLED STRUCTURES DEVELOPMENT OF A POSITION AND TRAJECTORY TRACKING CONTROL OF BALL AND PLATE SYSTEM USING A DOUBLE FEEDBACK LOOP STRUCTURE STOCHASTIC EVALUATION OF OFFSHORE CARBON FIBRE REINFORCED CONCRETE PLATFORMS ON ALUMINUM GIRDERS

click on whatsapp