DESIGN AND CONSTRUCTION OF A MULTIPERPOSE SECURITY SYSTEM WITH ALARM AND DISPLAY
By
EMEKA AJALA EE/H2003/034
Presented To
Department of Electrical/Electronic Engineering
ABSTRACT
This project report is a thesis written specifically to cover the design analysis construction, test and packaging of a multipurpose security system from electric component that can be easily be obtainable from the market.
The report discusses the various unit and stages of the alarm system, thesis include:-
a) Clock generation and frequency division unit.b) The control and section unit, comprising of a one shot 555 timer multiplexer, sound amplifier and the latch.c) The detection and switching unit made up of the fire and burgler sensors and priority encoder.d) The output unit comprising of the visual display and audio systems. These units have been lucidly represented with block diagrams and the calculations and the analysis of each component in the circuit of each block were done in the subsequent chapters of this part.
However, my own project is designed to serve three purposes: to detect human touch, burglar operation and to detect fire, giving the corresponding alarms and indications.
In a situation where there is a need to monitor the movement of people in a confidential building or a restricted area or to alert security-men in the case of fire outbreak, multipurpose security system is an electronic gadget which detect human shadow, human touch and fire and alert security-men through an alarm and equally display the particular room or area in which the target was hit.
The multi-purpose security system uses Light Dependent Resistor (LDR) to sense human shadow, touch switch to sense human touch and thermistor to sense fire.
The circuit is enclosed in such a way that if he sensor are installed in each various room, say room 1,2 and 3 etc. If an intruder wants to break through, say room 2 once he touches the handle of the door, the touch sensor senses his touch, then triggers an alarm and display room 2 on a big display board. If to say, there is fire outbreak in the same room 2 the fire sensor will sense it, trigger an alarm and equally display room 2. This is also application to all the room that has the sensor.
Multipurpose security system can equally be applied in banks, industries, financial institutions, schools and home to help safeguard lives and property.
LIST OF FIGURES
1.1 Block diagram of multi-purpose alarm system
3.1 Flowchart on design and construction procedures
4.1 Internal circuit of 555 timer IC
4.2 Astable multivibrator circuit using inverters
4.3 Output waveform of 555 timer oscillator
4.4 Astable circuit configuration, using Rb = Rs + Rp
4.5 One short configuration using 555 timer IC unit
4.6 Waveform of triggered mode
4.7 One shot multivibrator circuit
4.8 Pin configuration of 74LS191
4.11 Functional block diagram for 74LS153
4.14 Circuit diagram of frequency multiplexer 74LS153
a) Basic common-emitter circuit
b) Load-line construction.
4.21 Transistor amplifier arrangement with signal symbol
4.22 Transistor amplifier arrangement with signal symbol
4.23 Amplifier configuration component values
4.31 Pin configuration of 74LS175
4.32 Functional block diagram of Quadruple D-type FF (74LS175)
4.41 Typical IC encoder
4.42 8 line-to-line priority encoder 74LS148
4.44 Bimetallic heat detector
4.45 Time temperature curve
5.1 Isometric diagram of package multi-purpose alarm system.
LIST OF TABLES
4.01 Table of various frequencies of operation from the oscillator unit
4.11 Table of result of frequency derision
4.12 Table for the 74LS153 multiplexer operation
4.31 Functional table for D-type flip flop 74LS175
4.41 Functional table of 74LS148 priority encoder.
LIST OF ABBREVIATIONS AND SYMBOLS
IC Integrated Circuit
O/P Output
I/P Input
Vcc +5 Volt Supply
GND Ground or Earth
NE Segment
FF Flip Flop
TTL Transistor-transistor logic
CMOS Complementary Metallic Oxide Semi Conductor Logic
CLK Clock
CLR Clear
F Frequency
C(exp) Exponential
C/M Count Up
C/O Count Down
EL Enabled Input
EO Enabled Output
NPN Negative-Positive-Negative
VCE Collector Emitter Voltage
VBE Base-Emitter Voltage
VCB Collector Base Voltage
Sat Saturation
IC Collector
IB Base Current
RB Base Current
L/S Loud Speaker
KΩ Kilo ohms
KHZ Kilo-hertz
Dip Dual in line package
V Volts
TABLE OF CONTENTS
Title page
Approval page
Dedication
Acknowledgement
Abstract
List of tables
List of abbreviations
Table of contents
CHAPTER ONE
Introduction
Objective of the project
Project layout
Background information
Block diagram
CHAPTER TWO
Literature Review
CHAPTER THREE
Detection and switching unit
Fire detector
Human shadow detector
Human touch sensor
The hatch circuit
The alarm circuit
The display board
Power supply unit
CHAPTER FOUR
Methodology
Obtaining project topic and specifications
Choosing a suitable circuit
Selecting component values
Circuit analysis
Construction and testing
CHAPTER FIVE
Design analysis
Frequency generation
Clock generation
Amplification stage
Operation of a transistor
Switching operation of a transistor
Transistor biasing
CHAPTER SIX
Test, demonstration and packaging
Test analysis
Voltage test
Continuity test
Clock test
Demonstration
Packaging
Construction
Tools and materials
IC sockets
Construction aids
Procedure
Precautions
CHAPTER SEVEN
Conclusion and Recommendations
REFERENCES
- FOR ENQUIRY
- [email protected]
- 09019904113
About E-Project Material Centre
E-Project Material Centre is a web service aimed at successfully assisting final year students with quality, well researched, reliable and ready made project work. Our materials are recent, complete (chapter 1 to Minimum of Chapter 5, with references) and well written.INSTANT ACCESS! INSTANT DOWNLOAD. Simply select your department, choose from our list of topics available and explore your data
Why Students Love to Use E-Project Material ?
Guaranteed Delivery Getting your project delivered on time is essential. You cannot afford to turn in your project past the deadline. That is why you must get your project online from a company that guarantees to meet your deadline. e-Project Topics Material Centre is happy to offer instant delivery of projects listed on our website. We can handle just about any deadline you send our way. Satisfaction Guaranteed We always do whatever is necessary to ensure every customer's satisfaction
Disclaimer
E-Project Topics Material Centre will only provide projects as a reference for your research. The projects ordered and produced should be used as a guide or framework for your own project. The contents of the projects should be able to help you in generating new ideas and thoughts for your own project. It is the aim of e-Project Topics Centre to only provide guidance by which the projects should be pursued. We are neither encouraging any form of plagiarism nor are we advocating the use of the projects produced herein for cheating.
Terms and Condition
Using our service is LEGAL and IS NOT prohibited by any university/college policies You are allowed to use the original model papers you will receive in the following ways:
- As a source for additional understanding of the subject
- As a source for ideas for you own research (if properly referenced)
- For PROPER paraphrasing ( see your university definition of plagiarism and acceptable paraphrase) Direct citing ( if referenced properly)
